Setup Arctic Coin Masternode VPS - Step by Step

Easy video and step by step tutorial on how to setup Arctic Masternode.

Things Needed:

VPS From Vultr : https://goo.gl/mxcb24
1000.01 Tokens from Cryptopia : https://goo.gl/auqctL
FTP : fillezilla
Putty : http://www.putty.org/

---

Step 1
Run these commands:

adduser newUsername usermod -aG sudo newUsername

Step 2:
Run these commands to make a swapfile (for small VPS) :

sudo dd if=/dev/zero of=/var/swap.img bs=1024k count=1000 sudo mkswap /var/swap.img sudo swapon /var/swap.img

Run free again to confirm you now have a swapfile. Note: If you chose a different server
option from Vultr, with less RAM, you’ll need a LARGER swapfile, i.e. set the count
parameter to something larger like 2048, 4096 etc. If the compilation steps fails partway
through this is usually the reason.

To make the swap file persist when the server is rebooted:

sudo chmod 0600 /var/swap.img sudo chown root:root /var/swap.img sudo nano /etc/fstab

Append the following line to the end of the file:

/var/swap.img none swap sw 0 0

Save the file and exit

Step 3: Firewall ( can do this step at anytime )

sudo ufw allow OpenSSH sudo ufw allow 7209 sudo ufw default deny incoming sudo ufw default allow outgoing sudo ufw enable

Step 4
sudo apt-get install -y build-essential software-properties-common autoconf libssl-dev libboost-dev libboost-chrono-dev libboost-filesystem-dev libboost-program-options-dev libboost-system-dev libboost-test-dev libboost-thread-dev sudo automake git sudo add-apt-repository ppa:bitcoin/bitcoin -y

Step 5
sudo apt-get update sudo apt-get install libdb4.8-dev bsdmainutils libdb4.8++-dev -y mkdir ~/arc

Step 6

cd ~/arc
wget https://github.com/ArcticCore/arcticcoin/releases/download/v0.12.1.2/arcticcore-0.12.2-linux64.tar.gz
tar -xvf arcticcore-0.12.2-linux64.tar.gz mv arcticcore-0.12.1/* ./ rm arcticcore-0.12.2-linux64.tar.gz rm -r arcticcore-0.12.1/ sudo cp ~/arc/bin/arcticcoind /usr/local/bin/ sudo cp ~/arc/bin/arcticcoin-cli /usr/local/bin/ sudo cp ~/arc/bin/arcticcoin-tx /usr/local/bin/

Step 7 Create and edit conf
mkdir .arcticcore nano .arcticcore/arcticcoin.conf

rpcuser=user
rpcpassword=ASecurePasswordThatYouDontNeedToRemember
server=

Save & Exit

Step 8

arcticcoind -daemon arcticcoin-cli getinfo arcticcoin-cli getnewaddress 0 => address

Save the output of the last command, this is the address you'll send your ARC to.
Send EXACTLY 1000 ARC this address (1000.01 from cryptopia)

Then list transaction to make sure its there:
arcticcoin-cli listtransactions

and get the txid Save to a text file

Check to make sure your balance is there once synced all blocks and you have 15 Confirmations
arcticcoin-cli getbalance => 1000.00000000

Step 9
arcticcoin-cli goldminenode genkey =><SAVE_THIS_GEN_PRIVATE_KEY_FOR_CONF> arcticcoin-cli stop nano .arcticcore/arcticcoin.conf

And edit the conf file again and copy the code below:

~~
server=1
listen=1
daemon=1
goldminenode=1
goldminenodeprivkey= genkey
externalip=<YOUR_SERVER_IP>
~~

Step 10
arcticcoind -daemon arcticcoin-cli goldminenode outputs => { "xxxx": "IDX" } Note the "IDX" value and open the file "nano ~/.arcticcore/goldminenode.conf". Add the following line: mn1 <YOUR_SERVER_IP> :7209 GENKEY TXID +1 Then save and start the masternode Then arcticcoin-cli goldminenode start. Check your goldmine is connected by doing: arcticcoin-cli goldminenode list | grep 63ab96564e93c676e65f502f24fc254ef599eb051fe52e61f63632206c6f52fb "TXID-IDX": "PRE_ENABLED" After 20-30 min you should see: arcticcoin-cli goldminenode list | grep txid "AAAAA-B": "ENABLED" Like my content? You can tip me here: BTC: 1BKAbcowg68WytyPbwbFihNJBXpPSFj6u1 ETH: 0xA25D845E0f5F4D0c84770B02Cfb1ea80518e978B